Quick Start for:
State Purchasing

425/specs/cs-01

Texas Specification No. 425-CS-01

Effective Date: August 22, 1990

Reformatted Date: June 28, 1996

SPECIFICATION

for

CASEGOODS, SLAB (Panel) END STYLE, WOOD

1. SCOPE: This specifications establishes the minimum requirements for twenty-three (23) types of slab end wood casegoods that utilize the slab end style of construction with a recessed approach side. Wood veneers shall be walnut with walnut or mahogany finish, or medium oak finish on oak veneer. Worksurfaces shall be a closely matching high pressure laminate. These requirements are based on general industry standards for wood casegoods and are intended to provide high quality wood casegoods that are built for long and severe use and are compatible with existing slab end design furniture.

2. APPLICABLE SPECIFICATIONS AND STANDARDS: Reference to specifications, standards, test methods, and other documents shall be to the issues in effect on the date of the Invitation for Bids. Copies of the referenced documents may be obtained from the issuing organizations at the addresses shown. The following documents form a part of this specification to the extent specified herein:

2.1. AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI), 1430 Broadway, New York, NY 10018.

2.1.1. ANSI A208.1-89 -- Particleboard, Mat-formed Wood.

2.1.2. ANSI Z34.2-87 -- Self Certification by Producer or Supplier.

2.1.3. ANSI/BIFMA X5.5-89 -- Office Furnishing, Desk Products: Tests.

2.2. FEDERAL SPECIFICATIONS: Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402:

2.2.1. LLL-B810B -- Building Board (Hardboard) Hard Pressed Vegetable Fiber.

2.3. NATIONAL ELECTRICAL MANUFACTURES ASSOCIATION (NEMA), 2101 L Street, NW, Washington, DC 20037:

2.3.1. LD3-85 -- High Pressure Decorative Laminate.

2.4. STATE OF TEXAS SPECIFICATIONS, Texas Procurement and Support Services, P.O.Box 13186, Austin, TX 78711:

2.4.1. Commodity Book.

3. CLASSIFICATION: Slab end casegoods shall be classified by type, size, type number, and contract commodity group as shown in Table No. One.

4. DEFINITIONS: Terminology used in this specification is intended to be generic in nature and consistent with meanings that have been defined through general use, industry standards, and accepted trade practices. Where variant meanings may exist, the applicable interpretation shall be determined by the Texas Procurement and Support Services (TPASS).

4.1. Commission: The Texas Procurement and Support Services (TPASS).

4.2. "L" Return: A unit which si generally attached to a single pedestal desk, right or left side, to create a worksurface that extends at ninety degrees (90 ) to the desk work station. SE-R is at machine height, only. SE-CR and SE-ER are at both machine and desk height.

4.3. Secretarial "U": A unit which consists of:

4.3.1. A single pedestal desk right or left (R or L);

4.3.2. Either a flush or dropped down "bridge" with modesty panel (R or L);

4.3.3. A single pedestal rear worksurface, the same width as the main desk, minimum twenty inches (20") depth, at desk height.

4.4. Normal Use: Use which can reasonably be expected in a general office setting operating on a standard forty (40) hour work week. Normal use shall include incidental bumps and scrapes which can occur while swiveling, tilting, or moving a chair in close proximity to desks.

4.5. High Pressure Laminate (HPL): Multiple layers of resin impregnated paper fused under heat and pressure to result in a rigid covering media (minimum .040 inches thick).

4.6. Approved Product List (APL): A reference listing of casegood types of specific design and manufacture which have been inspected and evaluated by the Commission and approved for purchase under the provisions of this specification.

4.7. "M" Height: Machine (keyboard) height which is twenty-six-and-one-half inches to twenty-seven-and-one-half inches (26-1/2" to 27-1/2").

4.8. "D" Height: Desk height which is twenty-eight inches to thirty inches (28" to 30").

4.9. Abbreviations:

Bookcase BC
Box/Box/File B/B/F
Box/File B/F
Cathode Ray Tube (Computer Terminal) CRT
Central Locking C/L
Conference Conf.
Credenza Cred.
Executive Exec.
Hinge Door Cabinet HDC
Keyboard Drawer kbd
Kneespace KS
Lateral File, 2 Drawer LF
Not Applicable N/A
Pedestal Ped.
Rectangular Rect.
Right or Left R or L
Secretarial Sec.
With w/
Worksurface W/S

5. REQUIREMENTS: Products furnished under this specification shall meet or exceed the following requirements:

5.1. General Requirements:

5.1.1. Casegoods furnished under this specification shall meet or exceed the requirements of ANSI/BIFMA X5.5.

5.1.2. Casegoods shall be new, unused, currently standard of products of an established manufacturer except for such deviations as may be required by this specification.

5.1.3. Units shall be free of all imperfections, defects, and hazards which might affect appearance, normal life, serviceability, or user safety.

5.1.4. Details not specifically defined herein shall be in accordance with the best commercial practice for products of this type.

5.2. Design Requirements:

5.2.1. Casegoods shall exhibit slab end styling with recess approach side and three-fourths (3/4) modesty panels.

5.2.2. Each unit shall be standard with walnut finish on walnut vertical veneers with matching walnut high pressure laminate tops and be available in medium oak finish on oak vertical veneers with matching high pressure laminate tops, and mahogany finish on walnut vertical veneers with matching mahogany finish high pressure laminate tops.

5.2.3. End panels shall be banded by a minimum one-fourth inch (1/4") hardwood rim.

5.2.4. The backs of all units shall be finished (including bookcases, hutches, lateral files and credenzas).

5.3. Features:

5.3.1. Group 425-21-(13, 17) Desks: Types SE-(JE and C/E). Desk design shall be as specified herein and shall conform to industry standard for executive style, double pedestal desk.

5.3.1.1. Arrangement: Each executive desk shall contain three (3) box drawers in one (1) pedestal, one (1) box drawer and one (1) file drawer in the other pedestal. There shall be a kneespace drawer. Grommets shall be available in the GM, GZ and GN positions.

5.3.2. Group 425-21(22, 26, 30) Desks:

5.3.2.1. Type No. One: SE-E (R or L) with SE-ER (R or L).

5.3.2.2. Type No. Two: SE-CRT (R or L) with SE-CR (SE-CR (R or L).

5.3.2.3. Type No. Three: SE-S (R or L) or SE-R (R or L).

Desk design shall be a s specified herein and shall conform to industry standards for executive, CRT and secretarial style desks with "L" returns. The main desk shall be available with grommets in the GM, GQ, and GN positions. Right pedestal desks shall also be available with grommets in the GE position. Left pedestal desks shall also be available with grommets in the GF position.

5.3.2.4. Executive and CRT Arrangement: Each SE-E and SE-CRT unit shall have one (1) file drawer, one (1) box drawer and a kneespace drawer in the main desk. The "L" return shall have one (1) tray, or three inch (3") box, and one (1) file drawer. The file drawer in the SE-CR shall be EDP depth to provide for filing of fourteen-and-seven-eighths inch (14-7/8") by eleven inch (11") printouts. The file bars shall be adjustable to accommodate letter, legal or EDP paper.

5.3.2.5. Secretarial Arrangement: Each Model SE-S desk shall have four (4) box drawers, a file drawer and a kneespace drawer. The kneespae drawer shall be in the main desk. There shall be a box and/or EDP pedestal in the return unit.

5.3.2.6. "L" Return Arrangement: Units shall have a modesty panel and shall be available with optional grommets in the GL, GX, GC, GY and GR positions.

5.3.3. Group 425 (21, 34) Desks:

5.3.3.1. Types SE-SU (R or L). Desk design shall be as specified herein and shall conform to industry standards for secretarial style "U" desks. The entire outside, approach, perimeter of the "U" shall be equipped with a modesty panel.

5.3.3.2. Type SE-SU. Each secretarial "U" main desk unit shall have one (1) file drawer, one (1) box drawer and a kneespace drawer in the main desk. The main desk shall be approximately seventy-two inches (72") wide and thirty-six inches (36") deep.

5.3.3.3. Type SE-B. The "bridge" shall be approximately forty-two inches (42") wide and twenty-four inches (24") deep and available in a "flush" D height with optional pull out or articulating keyboard pad, or "dropped down" M height. The bridge shall be standard with grommet and appropriate grommet hardware in the center near the approach edge of the worksurface.

5.3.3.4. Type SE-RW/S. The single pedestal rear worksurface shall be approximately seventy-two inches (72") wide by twenty inches (20") deep. The drawer pedestal (s) shall be located under the outside end of the worksurface and there shall be (as a standard) a grommet and appropriate grommet hardware in the center near the approach edge of the worksurface, box and/or EDP pedestal in rear worksurface.

The pedestal arrangement shall be one of the following as specified in the Invitation for Bids:

A two drawer, three-fourth (3/4) height, box and/or file drawer pedestal; or one (1) three-fourth (3/4) height, box/box/box pedestal. The pedestal shall have three (3) box drawers.

5.3.4. Group 425-14-(55, 59) Credenzas:

5.3.4.1. Type SE-(JC and CC). Modular top with cabinet arrangement, delivered "set up" as follows:

5.3.4.2. Types SE-(JC and CC). Modular top with cabinet arrangement, delivered "set-up" as follows:

5.3.4.3. Type SE-JC. The Executive Storage Credenza, has two (2) cabinets and a center bookcase. Each cabinet shall contain one (1) box drawer and one (1) file drawer equipped for either legal or letter size hanging files, at user's option. The bookcase shall have two (2) sliding doors and at least one (1) adjustable shelf. Optional grommets shall be available in the GM, GQ, and GN positions.

5.3.4.4. Type SE-CC. The clerical kneespace credenza, has two (2) cabinets separated by a kneespace area. Each cabinet shall contain one (1) box drawer and one (1) file drawer equipped for either legal or letter size hanging files, at user's option. The clerical credenza shall be available with optional keyboard drawer or articulating keyboard tray. Optional grommets shall be available in the GM, GQ, and GN positions.

5.3.5. Group 425-41-(26, 30) Files:

5.3.5.1. Types SE-(LFC and LF). The lateral files shall have modular top with one (1) or two (2) modular, two (2) drawer lateral file unit (s) delivered "set-up". Whether the four (4) drawer credenza or two (2) drawer lateral file, each drawer shall be equipped for letter and legal size hanging files at user's option, and shall be provided with a positive safety interlock mechanism.

5.3.6. Group 425-03-(31, 35) Bookcases:

5.3.6.1. Type SE-(BC-48 and BC-480). The forty-eight inch (48") high bookcase shall have one (1) stationary shelf (at manufacturer's option) and at least two (2) adjustable shelves. The file top forty-eight inch (48") high bookcase shall have two (2) adjustable shelves. Additional shelves and adjustable shelf pins shall be available as an option, when so specified in the Invitation for Bids. The base of each bookcase shall be designed for its specific use. The back shall be finished.

5.3.7. Group 425-03-39 Hutch:

5.3.7.1. Type SE-HTC. The open bookshelf hutch shall have one (1) fixed shelf with or without a top, and shall be available with optional doors (sliding, hinged, or flipper) when so specified in the Invitation for Bids. The back shall be finished.

5.3.8. Group 425-18-(53, 55) Stands: Both stands shall be available with optional dual wheel casters, (two (2) locking and two (2) non-locking), and a storage shelf. Casters will add a nominal two inches (2") to the overall height.

5.3.8.1. Type SE-CT. Computer table, machine height, when purchased with optional casters, shall be available with keyboard drawer or articulating keyboard tray. All units shall be standard with a grommet in back panel.

5.3.8.2. Type SE-PT. Printer table, machine height, with minimum seventeen inch (17") wide paper slot, and a "cut-out" for rear feeding printers, with paper catch shelf and cord management.

5.3.9. Group 425-21-(38, 42, 46, 50, 54) Conference Tables: Types SE-T (144, 120, 96, 84, and 72) tables shall have rectangular panel ends. SE-T(144, 120 and 96) shall have a minimum fourteen inch (14") overhang each end. SE-T (144 and 120) shall have a minimum eight inch (8") overhang each side; SE-t 96, three inch (3") overhang. SE-T(84 and 72) shall have a minimum seven inch (7") overhang each end and three inch (3") each side. SE-T(84 and 72) shall be designed for optional use as Table Desks. Chair arm clearance shall be approximately twenty-seven-and-one-fourth inches (27-1/4"). The supports shall be "panel end" style.

5.3.9.1. Two-piece Tops: Optional two-piece tops on SE-T(144 and 120) shall be engineered for a tight secure fit where tables join together. The two-piece top must be joined together using a level tight fastener or manufacturer's standard bracketry.

5.3.9.2. Panel End Supports: Each end panel shall be approximately two-and-one-fourth inches (2-1/4") thick and consist of two (2) pieces of particle board approximately one-and-one-eighth inches (1-1/8") thick and a minimum of forty-five pounds (45 lbs.) density per square foot.

Each end panel shall be veneered on two (2) sides. End panels shall have a radius rounded shape and be edged with approximately seven-eighths inch (7/8") thick solid hardwood. The bottom of the end panel shall be edged with seven-eighths inch (7/8") thick solid hardwood. All end panels to have adjustable levelers.

All tables shall have stretcher rails or keels that run parallel under the tope between the end panels for support to eliminate warpage. The rials must be made of solid hardwood approximately seven-eighths inch (7/8") by four inches (4").

5.3.9.3. Type SE-T 144. Shall have three (3) panel end supports. The one-hundred-forty-four inch by forty-eight inch (144" x 48") top shall be standard as one (1) piece, but if requested in the Invitation for Bids, the manufacture shall provide a two (2) piece top for installation maneuverability.

5.3.9.4. Type SE-T 120. Shall have a minimum of two (2) panel end supports. The one-hundred-twenty inch by forty-eight inch (120" x 48") top shall be standard as one (1) piece, but if requested in the Invitation for Bids, the manufacturer shall provide a two (2) piece top for installation maneuverability.

5.3.9.5. Type SE-T 96. Shall have two (2) panel end supports. Table shall have a ninety-six inch by forty-two inch (96" x 42") one (1) piece top.

5.3.9.6. Type SE-T 84. Shall have two (2) panel end supports. Table shall have a eighty-four inch by forty-two inch (84" x 42") one (1) piece top.

5.3.9.7. Type SE-T 72. Shall have two (2) panel end supports. Table shall have a seventy-two inch by thirty-six inch (72" x 36") one (1) piece top.

5.3.10. Group 425-21-(58, 62, 68) Occasional Tables:

5.3.10.1. Types SE-(CRT, SQT, and RET). The tables shall have a solid hardwood apron beneath top perimeter, or an undershelf for stability.

5.3.10.1.1. Type SE-CRT. Approximately forty-eight inches by twenty inches by sixteen inches high (48" x 20" x 16"H) cocktail table.

5.3.10.1.2. Type SE-SQT. Approximately twenty-eight inches square by twenty-two inches high (28" sq. x 22"H) occasional table.

5.3.10.1.3. Type RET. Approximately eighteen inches by twenty-four inches by twenty-two inches high (18" x 24" x 22"H) end table.

5.3.11. Dimensions: All slab end casegoods shall conform to the dimensional requirements shown in Table No. Two.

5.4. Fabrication:

5.4.1. General Construction: For the purposes of this specification the slab end style of construction shall allow several variations in the relationship between the slab and the top. A reveal is acceptable between the end panel and the top.

5.4.2. Acceptable Variations:

5.4.2.1. Top butts into slab end, and slab end protrudes above top.

5.4.2.2. Top butts into slab end, with top edge of slab end level with top.

5.4.2.3. Top overlaps, but does not protrude beyond outside edge of slab end. With the application it is understood that the one-fourth inch (1/4") hardwood band is unnecessary along the top of the end panel.

5.4.3. Joints: Tops, ends and back panels shall be joined by tenons and glue or equally suitable methods that result in rigid and extremely durable joints. The inner pedestal panel shall be securely joined to the back support of the unit to insure permanent squareness and stability. Where screws are sued to secure the joint, there must be a minimum of one (1) screw at the top and one (1) at the bottom. All thin edges shall be supported to prevent deflection.

All joints not specifically described herein shall be in accordance with accepted industry standards and shall be rigid in construction and well glued.

5.4.4. Grain of Veneers: Veneer grain shall run in a vertical direction on ends, back and modesty panels, and pedestals. If the grain on the drawers is vertical, the veneers shall be grain matched.

5.4.5. Modesty Panels: All desks, returns, credenzas and computer support tables shall be furnished with modesty panels.

5.4.6. Return Unit: The return units and conference table tops shall be completely assembled and required no tools other than a screwdriver or wrench to attach to the desk or table pedestals.

5.5. Finish:

5.5.1. Finish: The finish shall be full filled, low sheen lacquer.

5.5.2. Quality: Finish shall be of high quality associated with industry standards for top grade merchandise. Finish shall enhance the beauty of the wood and be resistant to prolonged contact with water, mild acids and alkalis, ball point pen inks, carbon paper, and other staining agents encountered in an office environment.

5.6. Construction: The casegoods components shall be constructed as specified herein.

5.6.1. Tops: All tops are to be one-and-three-sixteenths inches (1-3/16") minimum thickness and shall be standard with a top surface of high pressure plastic laminate as defined in NEMA LD3, and in Paragraph 5.7.2., an undersurface (Backersheet) of suitable moisture barrier sheet material, and an acceptable core as defined in Paragraph 5.7.4. It is imperative that the walnut and mahogany laminates closely match the walnut and mahogany finishes on the walnut veneers and solids. It is imperative that the oak laminate closely match the medium oak finish on oak solids and veneers. The State reserves the right of determination of laminate compatibility with wood finish. Bids may be rejected if laminate finishes are determined to be incompatible with wood finishes.

Minimally acceptable cores shall have three (3) plies of particle board or flakeboard as defined in ANSI A 208.1., or a single ply of particle board or flakeboard as defined in ANSI A 208.1. They shall be of sufficient strength, and designed to prevent top from warping while in normal use. Grommets for wire management shall be available to be located as specified by the agency and the Invitation for Bids.

An alternate acceptable desk top core shall be as follows:

A single ply of particleboard or flakeboard as defined in Paragraph 5.7.4. fortified by a steel tension rod which bridges the kneespace area. Then tension rod shall be of sufficient gauge, length, and positioning to prevent the top from warping while in normal use. The tension rod shall be affixed in such a manner as to preclude its pulling loose for the expected life of the top.

5.6.2. Drawers: Drawer fronts shall be either laminated construction on lumber core or a minimum three (3) ply balanced laminated construction on minimum forty-five pound (45 lbs.) density Northern fibercore material with face veneer on the exposed side. Drawer sides and backs shall be of solid or seven (7) ply furniture grade hardwoods, minimum seven-sixteenths inch (7/16") thick. All drawers, except the kneespace drawer, are required to be dovetailed on all four (4) corners (French dovetails are acceptable).

The kneespace drawer may be dovetailed at the manufacturer's option. The minimum acceptable drawer bottoms shall be one-eighth inch (1/8") thick hardboard with pained face to mach drawer finish. Bottoms shall be fitted into grooves on all four (4) sides with glue blocks or hot melt glue on the bottom surface.

All desk shall have a center, kneespace, drawer which locks all drawers when closed. All drawers, except the kneespace drawer, shall have positive stops. All drawers shall be chemically treated to prevent swelling and shrinking. Drawer pedestals shall be the largest width and depth normally provided for each respective chassis size of desks and/or credenzas supported by that pedestal.

5.6.2.1. All kneespace drawers shall have a pen and pencil try secured to the forward portion of the drawer for easy access.

5.6.2.2. Box drawers shall have a metal suspension, (track) or metal guides grooved into the drawer sides. The minimum load capacity shall be sixty pounds (60 lbs.) for metal suspensions.

5.6.2.3. the file drawer shall operate on full progressive suspension, (nylon or steel ball bearing rollers in metal channel tracks), and shall extend the entire drawer to allow complete access. The file drawer shall be equipped for letter or legal filing. Supports for hanging type folders shall be furnished. The minimum load capacity shall be one-hundred pounds (100 lbs.).

5.6.2.4. The optional pull-out keyboard drawers on CRT stands, desk height returns, and in-place-of-center (kneespace) drawers on desks and credenzas shall be approximately twenty-three inches (23") wide by seventeen inches (17") deep. The interior drawer construction shall be the same as box drawers. Visible wood shall be finished to match exterior vertical panels. Shall be considered factory installed.

5.6.2.5. The articulating keyboard tray shall be adjustable vertically, rotatively, and shall lock into position. The entire tray and supportive arm shall store beneath the worksurface. The tray and/or keyboard pad shall be wood and be finished to match the exterior vertical panels considered factory installed. The approximate dimensions in inches shall be:

5.6.2.5.1. Tray: Twenty-four inches (24") wide by nine-and-one-half inches (9-1/2") deep.

5.6.2.5.2. Vertical Adjustment: Minimum five-and-one-half inches (5-1/2").

5.6.2.5.3. Rotational Adjustment: Thirty to ninety degrees (30 - 90 ) left and thirty to ninety degrees (30 - 90 ) right.

5.6.2.5.4. In-out: Eleven inches (11") to fifteen-and-one-half inches (15-1/2").

5.6.2.6. The slanting-artition stationery tray shall be of appropriate size to fit into box drawers of desks and/or credenzas, whichever is specified in the Invitation for Bids.

5.6.3. Slab (Panel) Ends: Ends shall be solid wood or laminate minimum one-and-one-eighth inches (1-1/8") thick. the minimum acceptable construction shall be:

5.6.3.1. Three (3) ply core of forty-five pound (45 lbs.) density particle board with a screw holding capacity of two-hundred-twenty-five pounds (225 lbs.)

5.6.3.2. Outside veneer of genuine walnut as per Paragraph 5.4.4. and an inside veneer of matching walnut or mahogany stained hardwood or outside veneer shall be of genuine oak and an inside veneer of matching oak stained hardwood.

5.6.3.3. Top, bottom, front, and back edges banded in minimum one-fourth inch (1/4") walnut or oak or matching walnut or oak stained hardwood. Exception: The top band is not required on casegoods with the slab end configuration shown in Paragraph 5.4.2.3.. Two (2) one inch (1") minimum diameter glides with an adjustable range of at least three-fourth inch (3/4") shall be securely mounted in each slab end.

5.6.4. Panels: Panels for desks shall be minimum three (3) ply laminated construction of sufficient thickness and composition to maintain the integrity of the desk.

5.6.5. Dust Bottoms: Dust bottoms shall be provided in each pedestal.

5.6.6. Safety Interlock: All lateral file cabinets shall be provided with a positive mechanical interlock mechanism. The mechanism shall be such that under the condition where one (1) drawer is extended up to two inches (2") beyond the fully closed position, the safety interlock shall have been activated and no other drawer or shelf can be extended more than two inches (2") beyond the face of the cabinet.

5.6.7. Locks: The kneespace drawer, in desks, shall be equipped with a paracentric type locking device that will lock all drawers in one (1) operation. Two keys shall be furnished for each desk. Separate locks, similarly keyed, for each pedestal and kneespace drawer are acceptable on credenzas and pedestals of returns. Separate locks, per pedestal, shall be acceptable on main desks only when center drawers are replace by pull-out or articulating keyboard trays.

5.6.8. Grommets: Grommets with appropriate hardware and "under-top" wire management and/or pedestal access shall be provided when grommets are specified to pass wires through worksurfaces, CRT and secretarial tops. The grommet shall be provided in one (1) or both of the following styles:

5.6.8.1. Round Grommet: Approximately two-and-one-half inches (2-1/2") outside diameter with access and/or cover plate.

5.6.8.2. Rectangular Grommet: Minimum two inches (2") length by one inch (1") width, with access plate. Sleeve will pass a telephone amphenol.

5.6.8.3. Standard Positions: Specific positions is as follows: Dimensions are from grommet rim to top edge. Except where noted, position is six inches (6") from rear, six inches (6") from side. Grommet positions other than those listed are considered non-standard and are subject to an upcharge.

GROMMET CODES AND POSITIONS

Code Grommet Position
GL Left Rear Corner
GX Left Rear 20" from side
GC Center Rear
GY Right Rear 20" from side
CR Right Rear Corner
Code Grommet Position for Other Casegoods
CM Left 9" from rear, 20" from side
GN Right 9" from rear, 20" from side
GQ Center 9" from rear
Code Grommet Position for Single Pedestal Desks Only
GF Right centered
GE Left centered

5.6.9 Plate: Grommet covers and/or access plate shall be manufacturer's standard finish.

5.6.10. Panels: Panels for desks shall be minimum three (3) ply laminated construction of sufficient thickness and composition to maintain the integrity of the desk. All exposed panel veneers shall be book matched in sets for each type of casegood. There shall be no exposed flakeboard or particleboard. For example, all edges not banded with wood shall be sealed, glazed, or covered with a moisture resistant barrier.

5.7. Materials: The units shall be made of the following materials:

5.7.1. Wood: All exterior wood veneered surfaces shall be Grade I genuine American walnut or Northern oak veneers with no sap. The veneer shall be minimum one-thrity-sixth inch (1/36") thick before sanding and carefully book matched for color and grain. The veneer shall be in full length pieces, applied in balanced construction with no veneer joints less and one inch (1") from the edge of the panels. Exterior solid wood parts shall be manufacturer's standard hardwood. All wood shall be thoroughly air and kiln dried to a moisture content not to exceed seven percent (7%) at the time of assembly. All exposed wood and veneer shall be bright, well sanded and free from brashness, discoloration, worm holes, pits and shakes. All veneers shall be edge glued with moisture resistant resin glues. All exterior panels shall be book matched in sets for each desk. All wood shall be free of defects affecting appearance, durability or serviceability.

5.7.2. Desk Top Laminate: Tops shall be standard with high pressure plastic laminate meeting NEMA LD 3 specifications. The laminate shall be of a uniform quality, free from blisters, wrinkles, cracks, scratches, dent marks, heat marks or other defects. The laminate shall be .040" thick. The pattern shall closely match the veneer pattern of the desk pedestals and panels. The top surface shall have a non-glare or "matte" finish.

5.7.3. Hardware and Trim: The style of hardware and trim shall be the manufacturer's standard for the unit specified provided it compliments the general styling of the casegood. All metal hardware shall be solid plated metal and may have a protective lacquer finish. No painted finishes will be allowed. Drawers with recessed finger pulls or side pulls are acceptable in lieu of attached drawer pulls. One inch (1") diameter glides with minimum three-fourths inch (3/4") adjustment shall be standard on all free standing casegoods. Exception: File Top Bookcases and Hutches.

5.7.4. Particleboard (Flackeboard): Particleboard used in the construction of casegoods conforming to this specification shall be a furniture grade Northern variety with a minimum density of forty-five pounds (45 lbs.) per cubic foot and a screw holding capacity of two-hundred-twenty-five pounds (225 lbs.) minimum.

5.7.5. Hardboard or Fiberboard: Hardboard or fiberboard used shall be minimum Type II, Standard Hardboard of Federal Specification LLL-B 810.

5.7.6. Labeling: Each casegood shall have a permanently affixed tag or wood imprint showing the name of the manufacturer.

5.8. Options: Options shall be as specified in Paragraph 5.2. for individual groups and types.

6. Testing: Testing shall be done by, or at the direction of, the Commission and/or the receiving State agency. Tests shall be performed on samples submitted with the bid and/or on samples taken from regular shipments. In the event products tested fail to meet or exceed all conditions and requirements of this specification, the cost of the samples used and the cost of the testing shall be borne by the supplier.

7. SAMPLES: Unless otherwise specified in the Invitation for Bids, no prepurchase samples will e required. Testing shall be performed on samples taken from material supplied on regular orders. Should a pre-award sample be required, manufacturer and/or vendor must provide sample within ten (10) days of request.

8. INSPECTION: Products furnished under this specification shall be inspected by, or at the discretion of the Commission and/or the ordering State agency either at destination or place of manufacturer.

9. WARRANTY: All casegoods shall carry the manufacturer's standard warranty and shall be guaranteed against defects in materials, workmanship, and performance for a minimum of one (1) year. The warranty shall begin on the date of acceptance of the unit by the ordering agency. During this warranty period, the vendor shall repair or replace defective components and/or units at no cost to the State of Texas.

10. AVAILABILITY OF SERVICE AND PARTS:

10.1. Service: When so specified in the Invitation for Bids, the bidder shall submit a list of companies or individuals, and their addresses, who stock repair parts and who can perform service on the units furnished.

10.2. Parts: An adequate supply of repair parts shall be readily available for the expected life of all products furnished under this specification.

11. INSTRUCTION MANUAL: The vendor shall furnish the ordering agency with one (1) copy of operating and maintenance instructions for each unit delivered. The materials furnished shall include instructions for lubricating drawer suspension and instructions for cleaning and protecting the exterior finish.

12. PACKING AND/OR PACKAGING: Packing shall be in accordance with recognized industry practices in a manner readily acceptable by common carriers engaged in interstate commerce. Within the shipping carton, units shall be packed in a manner designed to minimize damages during shipment due to rough or improper handling.

13. MARKING AND/OR LABELING:

13.1. Marking: Each shipping container shall be clearly marked with:

13.1.1. Name of contents.

13.1.2. Handedness of single pedestal desks and returns.

13.1.3. Quantity contained.

13.1.4. Order number or contract number.

13.1.5. Name and address of ordering agency.

13.1.6. Agency requisition number.

13.1.7. Name and address of the manufacturer.

13.2. Labeling: Each product shall bear a securely affixed and durable label showing the following:

13.2.1. Manufacturer's name.

13.2.2. Manufacturer's trademark.

14. BID LITERATURE: All bids shall be accompanied by a complete and illustrated description of the products being offered.

15. COMPLIANCE: In order for consideration to be given to the bid on an item under this specification, the bidder must comply with the following conditions:

15.1. Product Identification: The make and model number, name of the manufacturer, brand or trade name etc., as applicable, of the item which the vendor proposed to furnish must be stated as part of the bid.

15.2. Exceptions: Notwithstanding the above, any exception taken by the bidder to the requirements and conditions of this specification must be stated and described in detail as a part of the bid. If no exceptions or deviations are identified in this manner, the items must be furnished exactly as described herein.

15.3. Proof: The bidder shall bear the burden of proof of compliance with this specification.

15.4. Bid Response: Bidders shall provide a line item by line item written answer to all technical specifications of Paragraph 5.

Failure to submit line item answer at time of bid opening will result in disqualification of the bid.

16. APPROVED PRODUCTS LIST: The Commission shall maintain an Approved Products List (APL) of units which meet or exceed the requirements of this specification. Listing as an acceptable product shall be required for all casegood purchased under this specification.

16.1. Listing: The manufacturer or vendor shall comply with the following to have a product listed in the APL:

16.1.1. First, verify that your products meet or exceed each requirement of this Texas Specification.

16.1.2. Second, submit one (1) sample of each model for which approval is sought. Samples will be inspected and evaluated by the Commission's Inspector, and those models which are found to be acceptable will be listed as an approved product. Samples shall be provided in accordance with Paragraph 16.2. of this specification.

16.2. Evaluation: Samples shall be shipped only upon receipt of authorization from the Commission's Purchaser "N". Requests for authorization to ship samples shall be sent to the address shown in Paragraph 18. Samples shall be furnished at no cost to the State and with the understanding that such samples might be destroyed during the inspection and evaluation process. Once the casegoods have been listed as an approved product, additional prepurchase samples will generally not re required. Samples for random inspection and testing shall be selected from shipments to ordering agencies.

16.3. Continued Compliance: Listing as an acceptable product shall not relieve the manufacturer or vendor of the continuing obligation to provide products meeting or exceeding each requirement of this specification.

The manufacturer or vendor shall notify the Commission's Purchaser "N", in writing, of any changes in the product. Manufacturers and vendors shall also be responsible for submitting changes in addresses, brand or trade names, etc. to Purchaser "N". Failure to do so may result n the removal of the product from the APL. Changes which are deemed significant by Purchaser "N" shall be grounds for requiring re-approval of the product.

16.4. Removal and/or Re-listing: Approved products may be removed from the APL by subsequent noncompliance with the requirements of this specification, as determined by the Commission, or for failure to provide notification of any change in the approved product. Products which have been removed for the APL may be re-listed in accordance with Paragraph 16.1.

16.5. Referenced Manufacturers: Refer to Attachment No. One for manufacturers and respective model numbers.

17. ORDERING DATA: When ordering products conforming to this specification, the requesting agency shall specify the following:

17.1. The number of this specification (425-CS-01).

17.2. Type and type-number (See Table No. One and Paragraph 5.3.).

17.3. Handedness of single pedestal returns (Secretarial L or U desks only). (See Paragraph 4.1.).

17.4. Finish (See Paragraph 5.2.2).

17.5. Options (See Paragraph 5.3.).

17.6. Stationery tray size (See Paragraph 5.6.2.6.).

17.7. Service list (See Paragraph 10.1).

17.8. Quantity required of each model.

18. AVAILABILITY OF SPECIFICATIONS: Copies of this specification may be obtained by writing or calling:

Bid Services

Texas Procurement and Support Services

P.O. Box 13186

Austin, TX 78711-3047

512-463-3416

TABLE No. ONE

SLAB (Panel) END

Type Description Size (Inches) (W x D x H) Type Number Commodity Group
1.00 Junior Executive Desk 72 x 36 x 30 SE-JE 425-21-13
2.00 Clerical/Executive Desk 60 x 30 x 30 SE-C/E 425-21-17
3.00 Executive Main Desk 72 x 36 x30 SE-E (R or L) 425-21-22
3a (R or L) Executive Return 60 x 20 x30 SE-ER (R or L) 425-21-22
4.00 CRT Main Desk (R or L) 66 x 30 x 30 SE-CRT (R or L) 425-21-26
4a (R or L) CRT Return3 45 x 24 x27 SE-CR 425-21-26
5.00 Secretarial Main Desk (R or L)3 60 x 30 x 30 SE-S (R or L) 425-21-30
5a (R or L) Secretarial Return3 42 x 20 x 30 SE-R (R or L) 425-21-30
6.00 Secretarial "U" Main Desk 72 x 26 x 30 SE-SU 425-21-34
6a "U" Bridge 42 x 24 x 27 SE-B 425-21-34
6b "U" Rear Worksurface 72 x 20 x 30 SE-R W/S 425-21-34
7.00 Executive Storage Credenza (BF, BC, B/F) 66 x 20 x 30 SE-JC 425-15-55
8.00 Clerical Kneespace Credenza (B/F, KS, B/F) 66 x 20 x 30 SE-CC 425-14-59
9.00 Lateral File Credenza (LF/LF) 68 x 20 x 30 SE-LFC 425-41-26
10.00 Two Drawer Lateral File 36 x 20 x 30 SE-LF 425-41-30
11.00 Freestanding Bookcase 36 x 14 x 48 SE-BC48 425-03-31
12.00 Filetop Bookcase 36 x 14 x 48 SE-BC480 425-03-35
13.00 Hutch for 66" Credenza 66 x 14 x 36 SE-HTC 425-03-39
14.00 Computer Table 30 x 30 x 27 SE-CT 425-18-53
15.00 Printer Table 30 x 30 x 27 SE-PT 425-18-55
16.00 144" Rect. Conference Table 144 x 48 x 30 SE-T144 425-21-38
17.00 120" Rect. Conference Table 120 x 48 x 30 SE-T120 425-21-42
18.00 96" Rect. Conference Table 96 x 42 x 30 SE-T96 425-21-46
19.00 84" Rect. Conference Table 84 x 42 x 30 SE-T84 425-21-50
20.00 72" Rect Conference Table 72 x 36 x 30 SE-T72 425-21-54
21.00 Cocktail Table 48 x 20 x 16 SE-CKT 425-21-58
22.00 Square Table 28 x 28 x 22 SE-SQT 425-21-62
23.00 Rect. End Table 18 x 24 x 22 SE-RET 425-21-68
  1. Sizes are approximate. See Table No. Two for ranges.
  1. See Paragraph 4.8. for definition of abbreviations.
  1. The "L" return unit shall have a modesty panel.

TABLE No. TWO

SLAB END

Description Width Depth 1 Height 1 Overhang

Approach 1

Overhang

Ends 1

KS Drwrs Approx Sq. In. w/s
Junior Executive Desk

Type SE-JE

72.00 36.00 30.00 6-9.5 0.00 X 2592.00
Clerical/Executive Desk

Type SE-C/E

60.00 30.00 30.00 6-9 0.00 X 1800.00
Executive Main Desk (R or L)

Type SE-E

72.00 36.00 30.00 6-9.5 0.00 X 2592.00
(R or L) Executive Return

Type SE-ER

60.00 18-20 30.00 0-.2 0.00 N/A 1080-1200
CRT Main Desk (R or L)

Type SE-CRT

66.00 30-36 30.00 3.75-6 0.00 N/A 1980-2376
(R or L) CRT Return

Type SE-CR

45-48 24.00 27.00 0-.2 0.00 N/A 1080-1152
Secretarial Main Desk (R or L)

Type SE-S

60.00 30.00 30.00 3.75-6 0.00 X 1800.00
(R or L) Secretarial Return

Type SE-R

40-47 20-25 27.00 N/A 0.00 N/A 755-940
Secretarial "U" Main Desk

Type SE-SU

72.00 36.00 30.00 4-6 0.00 X 2592.00
"U" Bridge

Type SE-B

42-50 24.00 27.00 0-.2 N/A N/A 1008-1200
"U" Rear Worksurface

Type SE-R/WS

72.00 20.00 30.00 0-.2 N/A N/A 1440.00
Executive Storage Credenza (BF, BC, B/F)

Type SE-JC

66-72 18-20 30.00 4-6

0-.2

N/A N/A 1188-1440
Clerical Kneespace Credenza (B/F, KS, B/F)

Type SE-CC

66.00 18-20 30.00 0-2.5 N/A N/A 1188-1440
Lateral File Credenza (LF/LF)

Type SE-LFC

68-72 18-20 30.00 0-2.5 N/A N/A 1224-1440
Two Drawer Lateral File

Type SE-LF

34-36 18-20 30.00 0-2.5 N/A N/A 62-720
Freestanding Bookcase

Type SE-BC48

36.00 11.75-14 48-52 0-2.5 N/A N/A 423-504
Filetop Bookcase

Type SE-BC480

36.00 11.75-14 48.00 0-2.5 N/A N/A 423-4504
Hutch for 66" Credenza

Type SE-HTC

64-66 14.00 36-37 N/A N/A N/A N/A
Computer Table

Type SE-CT

30-36 24-30 27.00 .2-1.5 N/A N/A 720-1080
Printer Table

Type SE-PT

30-36 24-30 27.00 .2-1.5 N/A N/A 720-1080
144" Rect. Conference Table

Type SE-T144

144.00 48.00 30.00 Side (s) 8-11 14-19 N/A 6912.00
Description Width Depth 1 Height 1 Overhang

Approach 1

Overhang

Ends 1

KS Drwrs Approx Sq. In. w/s
120" Rect. Conference Table

Type SE-T120

120.00 48.00 30.00 Sides (s) 8-11 14-19 N/A 5760.00
96" Rect. Conference Table

Type SE-T96

96.00 42.00 30.00 Side (s) 3-8 14-19 N/A 4032.00
84" Rect. Conference Table

Type SE-T84

84.00 42.00 30.00 Side (s) 3-8 7-14 N/A 3528.00
72" Rect Conference Table

Type SE-T72

72.00 36.00 30.00 Side (s) 3-5 7-12 N/A 2592.00
Cocktail Table

Type SE-CKT

48-50 20.00 16.00 N/A N/A N/A 960-1000
Square Table

Type SE-SQT

28-30 28-30 22.00 N/A N/A N/A 784-900
Rect. End Table

Type SE-RET

18-20 24-28 22.00 N/A NA/ N/A 432-560
  1. Note: Allowable tolerance in inches:
  2. Width: -1" +2"
  3. Depth: -1" +2"
  4. Height: -1-1/2" +1"
  5. Overhang: -1" +2"
  6. Worksurface Area: -20 square inches +60 square inches

ATTACHMENT No. ONE

SLAB END

APPROVED PRODUCTS LIST

Referenced Manufacturer's Walnut Model Numbers Oak Model Numbers Mahogany Model Numbers
Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-JE

3772-F-W

1000-W

4036-72

1116-CWP

F1772-1L-P w/CD

F1672-1L-P w/CD

10FC72

F5072

3772-F-0

1000-0

N/A

1116-MOP

F177-MO-P w/CD

F1672-MO-P w/CD

10FC72-Oak

F5172

3772-F-M/W

1000-M/W

7036-72

1116-MWP

F1772-25M-P w/CD

F1672-25M-P w/CD

10FC72 Mah

F5072-4000

Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-C/E

3760-F-W

1003-W

4030-60

1113-CWP

F1760-1L-P w/CD

F1660-1L--P w/CD

10F60

F5060

3760-F-0

1003-0

N/A

1113-MOP

F1760-MO-P w/CD

F1660-MO-P w/CD

10F60-Oak

F5160

3760-F-M/W

1003-M/W

7030-60

1113-MWP

F1760-251-P w/CD

F1660-25M-P w/CD

10F60-Mah

F5060-4000

Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-E

G-37-72SP-W

100F-SP-W

M4036-72

1119-(R or L)-CWP

M1772-(R or L)-1L-P w/CD

M1672-(R or L)-1L-P w/CD

10SP72

F5060

G-37-72-SP-O

1004-SP-O

N/A

1119-(R or L)-MOP

M1772-(R or L)-MO-P w/CD

M1672-(R or L)-MO-P w/CD

10SP72-Oak

SP5172(R or L)

G-37-72-SP-M/W

1004-SP-M/W

M7036-72

1119-(R or L)-MWP

M1772-(R or L)-25M-P w/CD

M1672-(R or L)-25M-P w/CD

10SP72-Mah

SP5072-(R or L)-4000

Referenced Manufacturer's Walnut Model Numbers Oak Model Numbers Mahogany Model Numbers
Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-ER (R or L)

G-37-72-2-RET-W

1004-60-RET-W

MCRT4029-60(MOD)

1102X(R or L)-CWP

ERT-6020-1L-P

ERT-6020-1L-P

10ER60

G-37-72-2-RET-0

1004-60-RET-0

N/A

1102X(R or L)-MOP

ERT-6020-MO-P

ERT-6020-MO-P

10ER60-Oak

G-37-72-2-RET-M/W

1004-60-RET-M/W

MCRT7029-60(MOD)

1102X(R or L)-MWP

ERT-6020-25M-P

ERT-6020-25M-P

10ER60-Mah

Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-CRT (R or L)

3762-72-SP-W

1005-66-SP-W

M4030-66

1117-66 (R or L)-CWP

M1776-(R or L)-1L-P w/CD

M1666-(R or L)-1L-P w/CD

10SP66

3762-72-SP-O

1005-66-SP-O

N/A

1117-66(R or L)-MOP

M1776-(R or L)-MO-P w/CD

M166-(R or L)-MO-P w/CD

10SP66-Oak

3762-72-SP-M/W

1005-66-SP-M/W

M7030-66

1117-66(R or L)-MWP

M1776-(R or L)-25M-P w/CD

M1666-(R or L)-25M-P w/CD

10SP66-Mah

Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-CR (R or L)

3762-3-CRT-RET-W

1005-CRT-RET-W

MCRT4027-45(MOD)

1102T(R or L)-CWP

# included in desk

# included in desk

10CP45

CRT5047(R or L)

3762-3-CRT-RET-0

1005-CRT-RET-0

N/A

1102T(R or L)-MOP

# included in desk

# included in desk

10CP45

CRT5147 (R or L)

3762-3-CRT-RET-M/W

1005-CRT-RET-M/W

MCRT7027-45-(MOD)

1102T(R or L)-MWP

# included in desk

# included in desk

10CP45

CRT5047(R or L)-4000

Referenced Manufacturer's Walnut Model Numbers Oak Model Numbers Mahogany Model Numbers
Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-S(R or L)

3762-SP-W

1005-SP-W

M4030-60

1117-(R or L)-CWP

M1760-(R or L)TH-1L-P w/CD

M1660-(R or L)-TH-1L-P w/CD

10SP60

SP5060(R or L)

3762-SP-O

1005-SP-O

N/A

1117--R or L)-MOP

M1760-(R or L)-TH-MO-P w/CD

M1660-(R or L)-TH-MO-P w/CD

10SP60-Oak

SP5160(R or L)

3762-SP-M/W

1005-SP-M/W

M7030-60

1117(R or L)-MWP

M1760-(R or L)-TH-25M-P w/CD

M1760-(R or L)-TH-25M-P w/CD

10SP60-Mah

SP5060(R or L)-4000

Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-R (R or L)

3762-RET-3-W

1005-RET-W

M4027-40

1101(R or L)-CWP

# included in desk

# included in desk

10SSU-3B

TRU5045(R or L)

3762-RET-3-O

1005-RET-O

N/A

1101(R or L)-MOP

# included in desk

# included in desk

10SSU-3B-Oak

TRU5145(R or L)

3762-RET-3-M/W

1005-RET-M/W

M7027-40

1101(R or L)-MWP

# included in desk

# included in desk

10SSU-3B-Mah

TRU5045(R or L)-4000

Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-SU (R or L)

UG-37-72-24-2-SP-W

UG-10-72-24-2-SP-W

M-4036-72

1100-US-CWP

UM1772-7224-(R or L)-1L-P w/CD

UM1672-7224-(R or L) -1L-P w/CD

10UWS

SP5072(R or L)

UG-37-72-24-2-SP-O

UG-10-72-24-2-SP-O

N/A

1100-US-MOP

UM1772-7224-(R or L)-MO-P w/CD

UM1672-7224-(R or L)-MO-P w/CD

10USW-Oak

SP5172(R or L)

UG-37-72-24-2-SP-M/W

UG-10-72-24-2-SP-M/W

M7036-72

1100-US-MWP

UM1772-7224-(R or L)-25M-P w/CD

UM1772-7224-(R or L)-25M-P w/CD

10UWS-Mah

SP5072(R or L)-4000

Referenced Manufacturer's Walnut Model Numbers Oak Model Numbers Mahogany Model Numbers
Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-B

UG-37-72-24-2-B-W

UG-37-72-24-2-B-W

N/A

# included in desk

# included in desk
# included in desk
# included in desk
EU5048

UG-37-72-24-2-B-O

UG-10-72-24-2-B-O

N/A

# included in desk

# included in desk
# included in desk
# included in desk

EU5148

UG--37--72--24--2--B--M/W

UG--10--72--24--2--B--M/W

N/A

# included in desk

# included in desk
# included in desk
# included in desk

EU5048--4000

Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-R W/S

UG-37-72-24-2-CA-W

UG-10-72-24-2-CA-W

N/A

# included in desk

# included in desk
# included in desk
# included in desk

CR5072-(MOD)

UG-37-72-24-2-CA-O

UG-10-72-24-2-CA-O

N/A

# included in desk

# included in desk
# included in desk
# included in desk

CR-5172-(MOD)

UG--37--72--24--2--CA--M/W

UG--10--72--24--2--CA--M/W

N/A

# included in desk

# included in desk
# included in desk
# included in desk

CR--5072--(MOD)-4000

Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-JC

3700-CA-72-W

1006--W

4020--66--6

11--252--66--CWP

CR1766D--1L--P

CR1666D--1L--P

10DC72

CR5071--HD

3700--CA--72--O

1006--0

N/A

111--252--66--MOP

CR1766D--MO-P

CR166D--MO-P

10DC72--Oak

CR5171--HD

3700--CA--72--M/W

1006--M/W

7020--66--6

11--252--66--MWP

CR1776D--25M--P

CR1666D--25M-P

10DC72--Mah

CR5071--HD--4000

Referenced Manufacturer's Walnut Model Numbers Oak Model Numbers Mahogany Model Numbers
Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-CC

3700-CA-66-KS-W

1007-66-W

4020-66-4

11-202-66-CWP

CR1766-1L-P w/CD

CR1666-1L-P w/CD

10DC66-3

CR5066-KS

3700-CA-66-KS-O

1007-66-O

N/A

11-202-66-MOP

CR1766-MO-P w/CD

CR1666-MO-P w/CD

10DC66-3-Oak

CR5166-KS

3700-CA-66-KS-M/W

1007-66-M/W

7020-66-4

11-202-66-MWP

CR1666-25M-P w/CD

CR1666-25M-P w/CD

10DC66-3-Mah

CR-5066-KS-4000

Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-LFC

3772-LF-4-W

1008-W

4020-36LF

11-2X2D6F-CWP

4FD1772L-1L-P

4FP1672L-1L-P

10LF-4

TU5060-2X50-LFD-N

3772-LF-4-O

1008-0

N/A

11-2X2D6F-MOP

4FD1772L-MO-P

4FD1672L-MO-P

10LF-4-Oak

TU5160-2X51-LFD-N

3772-LF-4-M/W

1009-M/W

7020-36LF

11-2XDLF-MWP

4FD1772L-25M-P

4FD1672L-25M-P

10LF-4-Mah

TU5060-2X50-LFD-N-4000

Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-LF

2736-LF-2-W

1009-W

4020-36LF

11-2DLF-CWP

2FD1736L-1L-P

2FD1636L-1L-P

10LF-2

50LFD-2

3736-LF-2-O

1009-O

N/A

11-2DLF-MOP

2FD1736L-MO-P

2FD1636L-MO-P

10LF-2-Oak

51-LFD-2

3736-LF-2-M/W

1009-M/W

7020-36LF

11-2DLF-MWP

2FD1736L-25M-P

2FD1636L-25M-P

10LF-2-Mah

50-LFD-2-4000

Referenced Manufacturer's Walnut Model Numbers Oak Model Numbers Mahogany Model Numbers
Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-BC48

3752-BC-W

1011-W

B 48-FBW

11-6BC-CWP

BC1748-FB-1L-P

BC1648-FB-1L-P

10BC-O

BC48-Wal

3752-BC-O

1011-O

N/A

11-6BC-MOP

BC1748-FB-MO-P

BC1648-FB-1L-P

10BC-O-Oak

BC48-Oak

3752-BC-M/W

1011-M/W

B48-FBM

11-6BC-CWP

BC1748-FB-25M-P

BC1648-FB-25M-P

10BC-O-Mah

BC48-4000

Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-BC480

3752-Single-W

1012-Single-W

B48-FBW-(MOD)

11-6TU-CWP

H1748(MOD)-1L-P

H1648(MOD)-1L-P

10BC-HC

BC48-Wal (MOD)

2752-Single-O

1012-Single-O

N/A

11-6TU-MOP

H1748-(MOD)-MO-P

H1648-(MOD)-MO-P

10BC-HC-Oak

BC48-Oak (MOD)

3752-Single-M/W

1012-Single-M/W

B48-FBM(MOD)

11-6TU-MWP

H1648-(MOD)-25M-P

H1648-(MOD)-25M-P

10BC-HC-Mah

BC48-4000 (MOD)

Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-HTC

3715-VSU-57-OS-W

1015-VSU-64-OS-W

4014-66

11-66TU-CWP

OU-1766-1L-P

OU-1666-1L-P

10RM66T

HU5066

3715-VSU-57-OS-O

1015-VSU-64-OS-O

N/A

11-66TU-MOP

OU-1766-MO-P

OU-166-MO-P

10RM66T-Oak

HU5166

3715-VSU-57-OS-M/W

1015-VSU-57-OS-M/W

7014-66

11-66TU-MWP

OU-1766-25M-P

OU-1666-25M-P

10RM66T-Mah

HU5066-4000

Referenced Manufacturer's Walnut Model Numbers Oak Model Numbers Mahogany Model Numbers
Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-CT

3736-27-CRT-W

1010-27-W

4024-36

11-CRT-30-CWP

CRT1736-1L-P

CRT1636-1L-P

10CRT-T

CRT5036FS(MOD)

3736-27-CRT-O

1010-27-O

N/A

11-CRT-30-MOP

CRT1736-MO-P

CRT1636-MO-P

10CRT-T-Oak

CRT5136FS(MOD)

2726-27-CRT-M/W

1010-27-M/W

7024-36

11-CRT-30-MWP

CRT1736-25M-P

CRT1636-25M-P

10CRT-T-Mah

CRT5036FS-4000(MOD)

Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-PT

3736-27-PRT-W

1010-27-PT-W

4024-30

11-CRT-30-CWP w/11-PS

CRP1736-1L-P

CRP1636-1L-P

10PR-T

CPT5036FS(MOD)

3736-27-PRT-O

1010-27-PT-O

N/A

11-CRT-30-MOP w/11-PS

CRP-1736-MO-P

CRP-1636-MO-P

10PR-T-Oak

CPT5136FS(MOD)

3736-27-PRT-M/W

1010-27-PT-M/W

7024-30PS

11-CRT-30-MWP w/11-PS

CRP-1736-25M-P

CRP-1636-25M-P

10PR-T-Mah

CPT5036FS(MOD)-4000

Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-T144

37-144-PT-W

10-14-PT-W

DTPW-4048-144

11-14448-TPB-CWP

RT-144SB-1-1L-P

RT-144SB-1-1L-P

10PT144

PT50144

37-144-PT-O

10-144-PT-O

N/A

11-14448-TPB-MOP

RT-144SB-1-MO-P

RT-144SB-1-MO-P

10PT144-Oak

PT5144

37-144-PT-M/W

10-144-PT-M/W

DTPW-7048-144

11-14448-TPB-CWP

RT-144SB-1-25M-P

RT-144SB-1-25M-P

10PT144-Mah

PT50144-4000

Referenced Manufacturer's Walnut Model Numbers Oak Model Numbers Mahogany Model Numbers
Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-T120

37-120-PT-W

10-120-PT-W

DTPW-4048-120

11-12048-TPB-CWP

RT120SB-1-1L-P

RT120SB-1-1L-P

10PT120

PT50120

37-120-PT-O

10-120-PT-O

N/A

11-12048TPB-MOP

RT120SB-1-MO-P

RT120SB-1-MO-P

10PT120-Oak

PT51120

37-120-PT-M/W

10-20-PT-M/W

DTPW-7048-144

11-12048TPB-MWP

RT120SB-1-25M-P

RT120SB-1-25M-P

10PT120-Mah

PT50120-4000

Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-T96

37-96-PT-W

10-96-PT-W

DTPW-4042-96

11-9642-TPB-CWP

RT4296SB-1-1L-P

RT4296SB-1-1L-P

10PT96

PT5096

37-93-PT-O

10-96-PT-O

N/A

11-9642-TPB-MOP

RT4296SB-1-MO-P

RT4296SB-1-MO-P

10PT96-Oak

PT5196

37-96-PT-M/W

10-96-PT-M/W

DTPW-7042-96

11-9642-TPB-CWP

RT4296SB-1-25M-P

RT4296SB-1-25M-P

10PT96-Mah

PT5096-4000

Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-T84

37-84-PT-W

10-84-PT-W

DTPW-4042-84

11-8442-TPB-CWP

RT4284SB-1-1L-P

RT4284SB-1-1L-P

10PT84

PT5082

37-84-PT-O

10-84-PT-O

N/A

11-8442-TPB-MOP

RT4284SB-1-MO-P

RT4284SB-1-MO-P

10PT84-Oak

PT5182

37-84-PT-M//W

10-84-PT-M/W

DTPW-7042-8S

11-8442-TPB-MWP

RT4284SB-1-25M-P

RT4284SB-1-25M-P

10PT84-Mah

PT4082-4000

Referenced Manufacturer's Walnut Model Numbers Oak Model Numbers Mahogany Model Numbers
Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-T72

37-72-PT-W

10-72-PT-W

DTPW-4036-72

11-7236-TPB-CWP

RT3672SB-1-1L-P

RT3672SB-1-1L-P

10PT72

PT5072

37-72-PT-O

10-72-PT-O

N/A

11-7236-TPB-MOP

RT3672SB-1-MO-P

RT3672SB-1-MO-P

10PT72-Oak

PT5172

37-72-PT-M/W

10-72-PT-M/W

DTPW-7036-72

11-7236-TPB-MWP

RT3672SB-1-1L-P

RT3672SB-1-1L-P

10PT72-Mah

PT5072-4000

Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-CKT

37-5020-W

10-5020-W

4050-CT(MOD)

1147E-CWP

T1748-1L-P

T1648-1L-P

10CRT48

CT5042(MOD)

37-5020-O

10-5020-O

N/A

1147E-MOP

T1748-MO-P

T1648-MO-P

10CRT48-Oak

CT5142-(MOD)

37-5020-M/W

10-5020-M/W

7050-CT(MOD)

1147E-MWP

T1748-25M-P

T1648-25M-P

10CT48-Mah

CT5042(MOD)-4000

Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-SQT

37-3030-W

10-3030-W

4028-ST(MOD)

1128E-CWP

1163030-1L-P

1163030-1L-P

10ST28

ST5026

37-3030-O

10-3030-O

N/A

1128E-MOP

T163030-MO-P

T163030-MO-P

10ST28-Oak

ST5126(MOD)

37-3030-M/W

10-3030-M/W

7028-ST(MOD)

1128E-MWP

T173030-25M-P

T173030-25M-P

10ST28-Mah

ST5026-4000

Referenced Manufacturer's Walnut Model Numbers Oak Model Numbers Mahogany Model Numbers
Alma

Alma

Boling

Indiana

Inwood

Inwood

Jasper

Jofco

Type SE-RET

37-30--W

10--2030--W

4020--ET(MOD)

1124E--CWP

T1730--1L-P

T1630--1L-P

10ET18--24

ET5026

37--2030-O

10--203O-O

N/A

1124E--MOP

T1730--MO-P

T1630--MO-P

10ET18--24--Oak

ET5126(MOD)

37--2030--M/W

10--203--M/W

7029--ET(MOD)

1124E--MWP

T1730--25M--P

T1630--25M-P

10ET18--24--Mah

ED5026--4000

Required Plug-ins